Page 1 of 1
Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 15:30
by Jerry
[Using v23.50.0200]
After I upgraded to v23.50.0200. the following color filter is no longer being rendered:
attr:junction AND prop:#HardLinks:>=1
I use it to mark folders where an external drive is currently mounted.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 16:17
by admin
Seems to work here.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 16:29
by admin
Ah, you want the color filter to pop up when the drive is mounted? (without pressing F5)
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 16:31
by Jerry
admin wrote: ↑26 Aug 2022 16:29
Ah, you want the color filter to pop up when the drive is mounted? (without pressing F5)
Yes, the color is activated only when the drive is actually attached and mounted.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 16:39
by admin
Should be fixed in next beta.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 18:01
by Jerry
admin wrote: ↑26 Aug 2022 16:39
Should be fixed in next beta.
Just installed beta 23.50.0207 with the change you made, but I am still not seeing the color rendered.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 18:45
by admin
But you do after F5?
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 18:54
by Jerry
admin wrote: ↑26 Aug 2022 18:45
But you do after F5?
Nope. No change after pressing F5. Also not working with /fresh.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 19:22
by admin
Cannot explain. Check your other color filters.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 19:37
by Jerry
admin wrote: ↑26 Aug 2022 19:22
Cannot explain. Check your other color filters.
All my other color filters are working as configured. I tried moving this filter to the very top of the list but still no show.
When I hover over the mount point, the tooltip says:
"Hard Links: The system cannot find the file specified."
Could that be a clue? I don't know what this info was showing before the upgrade. The drive is definitely mounted and working, though. I see the contents of the drive under the folder.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 19:58
by admin
Yep, good clue. Since 20220811, if hardlinks are asked from junctions, those junctions are resolved and the hardlinks of their targets are returned. I guess that does not make sense in your case?
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 20:07
by Jerry
admin wrote: ↑26 Aug 2022 19:58
Yep, good clue. Since 20220811, if hardlinks are asked from junctions, those junctions are resolved and the hardlinks of their targets are returned. I guess that does not make sense in your case?
I guess not. Is there any other way to set up this filter with the 20220811 changes? I have a folder with 2 dozen subfolders that are used as named mount points for external drives. But at any time, only a few drives are actually attached and mounted. And those are the ones I want to see colored.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 21:13
by admin
I removed the changes. They were crappy.
Re: Color Filter Not Working Anymore: attr:junction AND prop:#HardLinks:>=1
Posted: 26 Aug 2022 21:30
by Jerry
admin wrote: ↑26 Aug 2022 21:13
I removed the changes. They were crappy.
Ok, thanks. Working again with version 23.50.0208