Page 1 of 1

How to set a default tabset configuration?

Posted: 03 Feb 2020 12:58
by Mark.I
I'm trying XYplorer, it seems I can't define a specific tabset and make it the default one for all sessions, no matter how many changes I make to the tabs during a session:
- If I check save settings to apply to tabs, all the open tabs at end of session gets restored in the next session.
- If save settings applies to tabsets, my default tabset configuration gets replaced by the configuration at the end of the session.
- If save settings doesn't apply to tabset nor to tabs, XYplorer doesn't open my tabset and it starts with 'this PC' tabs instead.

Is it possible to configure a default tabset and have it open all the times with no changes? It seems quite a basic feature to me.

Tnx

Re: How to set a default tabset configuration?

Posted: 03 Feb 2020 15:24
by RalphM
You can define a default startup path but in order to load a tabset you would need to set a script to be run on startup which loads the desired tabset or switch off save on exit.
I have various tabsets for different tasks and open new tabs within them until I feel it has gotten too "dirty", then I just reload that tabset again and start over. This approach works a treat for me.

For more sophisticated work with tabsets there are also a couple scripts available in the scripts section of the forum that might be helpful.

PS: Almost forgot - Welcome to the forums!

Re: How to set a default tabset configuration?

Posted: 03 Feb 2020 17:18
by klownboy
The problem is you are probably saving settings on exit. If you have a bunch of tabs (default tabs), you can save them as a tabset. Those same tabs will be displayed when you restart. In Configuration > General > Startup & Exit > Save settings on exit. Un-check this setting and just save when you want to save. Also, under "Save Settings" look at your settings for "Include most recently-used lists on save". Under the "Apply to...", you can select which elements you want saved when XYplorer saves. You may want to keep the tabs and tabsets checked such that they are saved when you manually save especially if you want to change or update your defaults tabs or tabset since you are not saving on exit. Or if you'd rather you could still save settings on exit, but on exit, don't save the tab and tabsets so you'd have these unchecked in "Apply to...". Personally, I don't save on exit and save when I want to save.

A great tabset and layout manager script that RalphM referred to is "Session Manager" located here. With this script you can save many different tabset arrangements as well as layouts and bring them up when you want.

And, welcome to the forum.

Re: How to set a default tabset configuration?

Posted: 03 Feb 2020 20:58
by Mark.I
Ok, it seems that giving up the autosave option does the trick in a reasonable way already, provided that I save manually while both tabs and tabsets are selected for saving in the configuration | startup & exit menu.
I'm going to check the more sophisticated script-based solution later.

So, thank you both, and for the warm welcome too.

Re: How to set a default tabset configuration?

Posted: 22 Oct 2020 00:11
by WirlyWirly
Hello, I just started using XYPlorer and spent hours trying to solve the same issue as OP. Thanks for the solution, but a new question popped up... What are we saving when we choose 'Save settings'?

I was under the impressions 'Settings' was just another name for the configuration options. If I disable 'Save settings on exit', how will I know what options won't be saved if I close? Also, when I use 'File/Save Settings', my tabsets are reset and I have to redefine them, which is pretty annoying. If that happens I'll never be able to save my 'settings', whatever those are.

Settings and configuration are pretty much interchangeably used across computing, so this is pretty confusing.

Re: How to set a default tabset configuration?

Posted: 22 Oct 2020 00:29
by RalphM
Save settings is a general term for anything that changes the behavior or look of XY, so yes, it includes the configuration settings but also the changes you make to the layout while working with XY.
You can set in configuration (Start & Exit/Apply to) what is saved with some granularity.
As stated in an earlier post, the best solution for the OP's problem would rather be to use either the Session manager script or call a script on startup that loads the required tabset.

Re: How to set a default tabset configuration?

Posted: 28 Oct 2020 13:10
by xyplorerköln
Mark.I and WirlyWirly, I just wanted to second klownboy's recommendation to try out the Session Manager script. It's easy to install and use and will likely achieve all you want to do with tabsets.