Page 1 of 1
To have XY ignore two archival drives named I and J
Posted: 03 Oct 2016 23:17
by pat55
What is the best simple way to have XY ignore two archival drives named I and J?
These are duplicates of nearly everything (using GoodSync) and I rarely need to visit - except to see if all is well.
Reducing the total volume stored by half should make XY run faster - but by how much?
pat
Re: To have XY ignore two archival drives named I and J
Posted: 03 Oct 2016 23:22
by highend
Ignore in what way? Not showing them in the tree?
Re: To have XY ignore two archival drives named I and J
Posted: 03 Oct 2016 23:30
by pat55
Ignore in pretty much every way possible.
I was checking list management - looking at favored folders, files etc. and all the stuff under Recent Locations etc
and seeing I and J drive info that could be done without.
So I asked, what is perhaps a dumb question, to see what else I may have overlooked.
pat
Re: To have XY ignore two archival drives named I and J
Posted: 04 Oct 2016 01:14
by elqasar
There is a tweak in the XYplorer.ini you can use.
HideDrivesByLetter=IJ
Re: To have XY ignore two archival drives named I and J
Posted: 04 Oct 2016 01:54
by pat55
THANKS
I was hoping for that.
pat
Re: To have XY ignore two archival drives named I and J
Posted: 07 Oct 2016 04:49
by pat55
Inserted the magic line as shown. Did a reboot and found I and J drives have NOT been excluded.
Is there a different place that it should have been entered?
Some other thing that needs to happen to make this work?
I pasted from here and using ver 17.10.0007
pat
Re: To have XY ignore two archival drives named I and J
Posted: 07 Oct 2016 06:51
by highend
This tweak is in the "Settings" section, not in "General" and the entry already exists, it just needs to be filled with the drive letters...
Re: To have XY ignore two archival drives named I and J
Posted: 07 Oct 2016 18:35
by pat55
It did not work - even with H turned on or off and a reboot.
Re: To have XY ignore two archival drives named I and J
Posted: 08 Oct 2016 00:16
by pat55
Double checked that XYplorer.ini was changed correctly.
As you can see there is also a XYplorer02.ini - that mysteriously keep changing by itself - what is this file?
It also reflects the ver 17.10.0007 beta that I am using - is that where the changes should be made?????
Ignore vs. Hide
Ignore 'to me' means XY will run far faster because it has none of my files on I: and J:
Hide only means that I can not manipulate files on J & I - XY will maintain the files - and is therefore useless to me.
Suddenly I'm also unable to drag files to a different folder - what has been reset?????
and Where?
pat
Re: To have XY ignore two archival drives named I and J
Posted: 08 Oct 2016 09:29
by bdeshi
Menu > Tools > Open Configuration File will open the correct ini file for editing. Use this menu item, then exit XYplorer with the ini file open in editor, make and save changes, then start XYplorer.
pat55 wrote:Suddenly I'm also unable to drag files to a different folder - what has been reset?????
and Where?
Probably Tools > Customize List > Manual Sorting ?
Re: To have XY ignore two archival drives named I and J
Posted: 08 Oct 2016 18:24
by pat55
Correct Sammay - drag and drop BECAME ok when Manual Sorting was unchecked -I WAS JUST GETTING TO LIKE manual sorting!
This is the second time that you 'rescued' me - THANKS Sammay
Admin why can we not manual sort AND drag and drop - as in other programs??????
With manual sort and rename (shift+F2) I would very much prefer that the manual sort remained after a rename files. <-----
As a rule I use Modified and latest at the top which I get now. After a resort I need to do a Name sort to
see the new order and then back to manual sort. A REAL PAIN because it is so distracting because I typically
manual sort a folder or parts of a folder about three or more times!
pat
Why do I keep finding stuff like this in the sophisticated and mature program. :-)